Moisture and Mold-Resistant Drywall in Crystal River, FL

Moisture and mold-resistant drywall installation in Crystal River costs $2.25 to $3.75 per square foot in 2026, hung and finished. Standard drywall is paper over gypsum, and both halves of that sentence explain why it struggles in damp rooms: paper feeds mold, and gypsum softens wet. Glass-mat and mold-resistant boards remove the paper from the equation — but they are not waterproof, and we will not sell them as if they were.

Talk to a Drywall Specialist: (352) 670-3571

Check your ZIP

Type your ZIP code. We will tell you if we serve your street.

Worker displaying purple moisture-resistant drywall in Crystal River, FL

A job like this one

A bath and laundry shared one damp wall. The failed paper-faced board came out, the cavity read dry, and glass-mat board went in on the wet side with standard board — honestly specified — everywhere the exposure did not reach.

Sample price
$2.25 to $3.75 per sq ft, hung and finished
Sample turnaround
Two to four days with dry time for most rooms.
Worker holding purple moisture-resistant board in Crystal River, FL
Worker displaying purple moisture-resistant drywall in Crystal River, FL

Moisture board gets specified in the wrong places more often than it gets left out. The work starts by zoning the room: genuinely wet areas (behind tile, at showers) get cement backer; humid areas get moisture- or mold-resistant board; ordinary surfaces stay standard. Ventilation belongs in the same conversation — new board handles conditions better, but it does not fix a fan that does not move air.

What the job covers

What it does not cover

Built for Gulf humidity

This stretch of the Gulf Coast holds high humidity most of the year, and interiors feel it: AC-off hours in snowbird homes, canal-front air near Kings Bay, bath fans venting into attics. The board premium over standard is a modest part of a typical bath or laundry total, which is why the honest call is zoning, not blanket upgrades. Failed wet board that has to come out first is scoped on the water damage page.

Questions on moisture and mold-resistant drywall

Need help in Crystal River?

Call (352) 670-3571 or send the form. We will tell you plainly what the job needs and what it tends to cost before work starts.

Get a free estimate

Frequently Asked Questions

How is the price set?

Per square foot at $2.25 to $3.75 hung and finished. The board costs more per sheet than standard — and cement backer more again — so the zone mix across the room moves the rate.

Is mold-resistant board waterproof?

No. It means the board itself gives mold far less to feed on than paper-faced drywall — a real advantage in damp rooms — but standing water and leaks still have to be stopped at the source.

Should I put it everywhere?

Generally no, and it would be money spent for little return in dry living spaces. We zone it to baths, laundries, kitchens, and unconditioned rooms where exposure is real.

My bath has no fan problem — the walls still fail. Why?

Often the board is paper-faced in a room that never fully dries, or the fan vents into the attic instead of outside. We check both at the look and say which one your room has.

Is the site look free?

Yes. The look, the moisture read where a room has been wet, and the written quote cost nothing.

What Does My Drywall Project Cost?

Drywall is priced by the square foot of wall and ceiling surface — not by the size of your floor. That one fact explains most of the gap between quotes. Here are the ranges we see on real jobs around Crystal River, and a calculator built on the same numbers.

Drywall Repair & Patch

Most single repairs land between $250 and $800. Pros price patches by the square foot of damaged area — roughly $55–$75 a foot around Crystal River — but every repair carries a minimum job charge, because a patch takes the same setup and the same repeat trips for drying coats whether it's the size of a dinner plate or a door. Grouping several spots into one visit is the cheapest way to fix them: they share one minimum. Some repairs are priced flat by the job instead of the square foot: a cut-out ceiling section replaced and texture-matched (an 8×10 section ran $720 flat), long seam cracks (46 linear feet of re-taped seams across three rooms ran $540 flat), and popcorn removal finished smooth (230 sq ft ran $575 flat).

New Drywall Installation

For bare studs finished paint-ready (a standard Level 4 finish), plan on $1.60–$3.00 per sq ft of wall and ceiling surface, materials and labor included. A typical 12×12 bedroom with 8-foot ceilings — that's 528 sq ft of surface — runs about $890–$1,660 around Crystal River.

Room Remodel & Replacement

Tearing out old drywall and hauling it off adds $0.60–$1.25 per sq ft on top of new installation — a combined $2.20–$4.25 per sq ft. That same 12×12 bedroom, gutted and re-drywalled, runs about $1,210–$2,310. Opening walls can uncover surprises — water damage, old wiring — and those get priced once they're visible, never guessed at in advance.

Garage Drywall

Garages run $1.55–$3.30 per sq ft depending on finish. Code requires 5/8-inch fire-rated (Type X) board on the wall shared with the house, and on the ceiling when there's living space above it — that's the fire separation, not an upsell. Most two-car garages land between $1,900 and $4,100 finished.

Texture, Skim & Paint

On walls that are already up: skim coating runs $0.95–$1.30 per sq ft, orange-peel or knockdown texture $0.80–$1.85, and primer plus two coats of paint $1.05–$2.85. A typical room's walls — about 415 sq ft of surface — usually land between $750 and $1,980 for texture and paint together.

What Moves the Price

  • Finish level. A full Level 5 skim coat (for gloss paint or bright, raking light) costs more than standard paint-ready Level 4.
  • Ceilings. Overhead work runs roughly 20–25% more than the same area on a wall — lifts, heavier board, two sets of hands.
  • Ceiling height. Taller walls mean longer sheets, scaffolding, and slower work.
  • Texture matching. Blending a patch into existing orange peel or knockdown is hand work, and it's priced like it.
  • Tear-out. Removing old drywall and disposing of it is its own line on the quote.
  • Job size. Small jobs carry a minimum charge; on big jobs the setup spreads over more feet, so the per-foot price drops.

These are planning ranges, not a quote — your final price is confirmed after an in-person look, before any work starts.

A note on materials. These ranges are figured with standard drywall board and the finish level you pick above. Board isn't all the same price, though: moisture- and mold-resistant board — the green or purple board for bathrooms and basements — costs more a sheet than standard board, and on a big job that can push you toward the top of your range, or a little past it. Tell us where the work is and we'll confirm the exact board and the price at the in-person estimate, before any work starts.

Estimate Your Project

1 · Pick your project
Your estimated range

Free — no obligation. Your calculator numbers ride along with the request.

📞 (352) 670-3571