Metal Stud Framing in Crystal River, FL
Metal stud framing in Crystal River costs $1.50 to $3.00 per square foot of wall in 2026, for framing only — board and finish are priced apart or under one scope with our installation work. Steel behaves nothing like timber: it arrives straight, stays straight, and does not feed termites or rot in Gulf humidity. Framing also decides everything that follows; a wall finished over a crooked frame is a crooked wall.
Talk to a Drywall Specialist: (352) 670-3571
Check your ZIP
Type your ZIP code. We will tell you if we serve your street.

A job like this one
An office floor plate was set out from the drawings in a morning: lines snapped on the slab, track fixed, studs plumbed, openings squared for doors that hung true the first time — and the boarding crew, ours as well, lost no time shimming.
- Sample price
- $1.50 to $3.00 per sq ft of wall, framing only
- Sample turnaround
- Most partition packages frame in one to three days.

A frame built by the crew that also hangs the board is a different frame, which is why we take both stages on most projects. Lines are checked for square and dimension against the plan before any steel is fixed, deflection allowance is built in at the head where walls run to the deck, and backing goes in during framing — never as a later excavation.
What the job covers
- Interior office and tenancy partitions, set out from the floor plan at the specified gauge and spacing
- Full-height and deck-to-deck walls, with head deflection allowance so movement does not crack the finish
- Door, window, and opening framing with jamb studs, headers, and reinforcement
- Shaft and riser framing, soffits and bulkheads, plus steel or timber backing for TVs, cabinets, grab bars, and signage
What it does not cover
- Load-bearing steel work. This page is non-load-bearing interior framing; structural steel is an engineer's scope.
- Board and finish, unless quoted under one scope — the framing quote says plainly which it is.
- Other trades' rough-in. The frame is left open, plumb, and clear for electrical, mechanical, and plumbing.
Steel suits this coast
Commercial interiors around Crystal River — the Lecanto medical and office growth, US-19 retail, professional buildings in Inverness — lean on steel framing for the same reasons as anywhere, plus two local ones: it does not rot in unconditioned shells during slow build-outs, and termites ignore it. Framing most often pairs with our commercial installation and partition work under one scope.
Questions on metal stud framing
Need help in Crystal River?
Call (352) 670-3571 or send the form. We will tell you plainly what the job needs and what it tends to cost before work starts.
Get a free estimate
Related Services
Drywall Installation · Commercial Drywall Installation · Drywall Partition Installation · Fire-Rated Drywall Installation · Garage Drywall Installation · Moisture and Mold-Resistant Drywall · Residential Drywall Installation · Soundproof and Acoustic Drywall Installation · Suspended Ceiling Installation
Frequently Asked Questions
How is the price set?
Per square foot of wall at $1.50 to $3.00, framing only. Wall height, gauge, openings, and backing move the rate; board and finish are separate lines unless the quote combines them.
Why steel instead of wood studs?
Steel arrives straight and stays straight, so the finished wall is flatter with fewer surprises at finishing. It also does not rot or feed termites.
What gauge do I need?
It depends on what the wall is for — height, what it carries, and how flat the finish must be. The partition schedule or the look settles it, and the quote names it.
Can things be mounted on a metal-stud wall later?
Yes — provided backing went in during framing. That is why fixture positions are confirmed before the frame closes, and why we ask about TVs, cabinets, and rails up front.
Is the site walk free?
Yes. The walk, the takeoff from plans, and the written quote cost nothing.
What Does My Drywall Project Cost?
Drywall is priced by the square foot of wall and ceiling surface — not by the size of your floor. That one fact explains most of the gap between quotes. Here are the ranges we see on real jobs around Crystal River, and a calculator built on the same numbers.
Drywall Repair & Patch
Most single repairs land between $250 and $800. Pros price patches by the square foot of damaged area — roughly $55–$75 a foot around Crystal River — but every repair carries a minimum job charge, because a patch takes the same setup and the same repeat trips for drying coats whether it's the size of a dinner plate or a door. Grouping several spots into one visit is the cheapest way to fix them: they share one minimum. Some repairs are priced flat by the job instead of the square foot: a cut-out ceiling section replaced and texture-matched (an 8×10 section ran $720 flat), long seam cracks (46 linear feet of re-taped seams across three rooms ran $540 flat), and popcorn removal finished smooth (230 sq ft ran $575 flat).
New Drywall Installation
For bare studs finished paint-ready (a standard Level 4 finish), plan on $1.60–$3.00 per sq ft of wall and ceiling surface, materials and labor included. A typical 12×12 bedroom with 8-foot ceilings — that's 528 sq ft of surface — runs about $890–$1,660 around Crystal River.
Room Remodel & Replacement
Tearing out old drywall and hauling it off adds $0.60–$1.25 per sq ft on top of new installation — a combined $2.20–$4.25 per sq ft. That same 12×12 bedroom, gutted and re-drywalled, runs about $1,210–$2,310. Opening walls can uncover surprises — water damage, old wiring — and those get priced once they're visible, never guessed at in advance.
Garage Drywall
Garages run $1.55–$3.30 per sq ft depending on finish. Code requires 5/8-inch fire-rated (Type X) board on the wall shared with the house, and on the ceiling when there's living space above it — that's the fire separation, not an upsell. Most two-car garages land between $1,900 and $4,100 finished.
Texture, Skim & Paint
On walls that are already up: skim coating runs $0.95–$1.30 per sq ft, orange-peel or knockdown texture $0.80–$1.85, and primer plus two coats of paint $1.05–$2.85. A typical room's walls — about 415 sq ft of surface — usually land between $750 and $1,980 for texture and paint together.
What Moves the Price
- Finish level. A full Level 5 skim coat (for gloss paint or bright, raking light) costs more than standard paint-ready Level 4.
- Ceilings. Overhead work runs roughly 20–25% more than the same area on a wall — lifts, heavier board, two sets of hands.
- Ceiling height. Taller walls mean longer sheets, scaffolding, and slower work.
- Texture matching. Blending a patch into existing orange peel or knockdown is hand work, and it's priced like it.
- Tear-out. Removing old drywall and disposing of it is its own line on the quote.
- Job size. Small jobs carry a minimum charge; on big jobs the setup spreads over more feet, so the per-foot price drops.
These are planning ranges, not a quote — your final price is confirmed after an in-person look, before any work starts.
A note on materials. These ranges are figured with standard drywall board and the finish level you pick above. Board isn't all the same price, though: moisture- and mold-resistant board — the green or purple board for bathrooms and basements — costs more a sheet than standard board, and on a big job that can push you toward the top of your range, or a little past it. Tell us where the work is and we'll confirm the exact board and the price at the in-person estimate, before any work starts.
Estimate Your Project
Measure the damaged section itself — length × width. A full 4×8 sheet section is 32 sq ft.
Spots done in one visit share a single minimum charge.
Price includes tearing out the old drywall and hauling it off.
Includes 5/8″ Type X fire-rated board on the wall shared with the house — and on the ceiling when there is living space above it — as code requires.
Free — no obligation. Your calculator numbers ride along with the request.
Send Your Project to Crystal River Drywall Specialists
Your estimate is attached automatically. Add your info and — if you can — a few photos of the project. Photos help us price the job before we ever set foot in the house. Prefer to talk? Call (352) 670-3571.