Fire-Rated Drywall Installation in Crystal River, FL

Fire-rated drywall installation in Crystal River costs $3.50 to $6.00 per square foot in 2026, built to the assembly detail in the project drawings. This is the one area of drywall work where how a wall is built matters more than how it looks: the rating belongs to the tested assembly — board type, layers, framing, fastening, and terminations together — never to a sheet of board alone.

Talk to a Drywall Specialist: (352) 670-3571

Check your ZIP

Type your ZIP code. We will tell you if we serve your street.

Two workers installing drywall panels on insulated studs in Crystal River, FL

A job like this one

A garage separation and a shop demising wall were built the same week: Type X board in the specified layers, joints offset between layers, penetrations treated, and progress photos taken before closing — both passed their inspections without a revisit.

Sample price
$3.50 to $6.00 per sq ft to the specified assembly
Sample turnaround
Set by the project program and its inspection points.
Commercial interior with blue drywall boards installed in Crystal River, FL
Commercial interior with blue drywall boards installed in Crystal River, FL

Rated assemblies fail inspection over details, not big mistakes: a joint landed wrong, a layer short, a termination that stops at the ceiling grid instead of the deck. So the sequence carries verification inside it — assembly reviewed before framing, rough-in and penetration treatment coordinated, layers photographed where the builder wants a record.

What the job covers

What it does not cover

Where rated walls show up here

Rated construction turns up across the whole local range: every attached garage in the county's housing, the demising walls between shops along the retail corridors, medical and multi-occupancy buildings in Lecanto and Homosassa Springs, and shafts in the low-rise commercial stock. The garage case is the everyday one — it is also covered from the homeowner side on the garage installation page.

Questions on fire-rated drywall installation

Need help in Crystal River?

Call (352) 670-3571 or send the form. We will tell you plainly what the job needs and what it tends to cost before work starts.

Get a free estimate

Frequently Asked Questions

How is the price set?

Per square foot at $3.50 to $6.00, by assembly: number of layers, board type, height, and termination detail. The quote lists each rated wall type with its assembly reference where one is provided.

Is fire-rated board fireproof?

No — and that is the most common misunderstanding in this work. A rated assembly resists fire for a tested period as a system; the board alone carries no rating.

Does my garage wall really need this?

Separation between an attached garage and living space is a standard requirement in residential construction. The specific assembly for your project comes from the code and your plans, which we check at the look.

What happens at pipes and wires through a rated wall?

Penetrations are treated so the assembly still performs. The treatment depends on what passes through and which assembly it crosses, and it is coordinated before closing.

Is the site walk free?

Yes. The walk, the assembly review against your drawings, and the written quote cost nothing.

What Does My Drywall Project Cost?

Drywall is priced by the square foot of wall and ceiling surface — not by the size of your floor. That one fact explains most of the gap between quotes. Here are the ranges we see on real jobs around Crystal River, and a calculator built on the same numbers.

Drywall Repair & Patch

Most single repairs land between $250 and $800. Pros price patches by the square foot of damaged area — roughly $55–$75 a foot around Crystal River — but every repair carries a minimum job charge, because a patch takes the same setup and the same repeat trips for drying coats whether it's the size of a dinner plate or a door. Grouping several spots into one visit is the cheapest way to fix them: they share one minimum. Some repairs are priced flat by the job instead of the square foot: a cut-out ceiling section replaced and texture-matched (an 8×10 section ran $720 flat), long seam cracks (46 linear feet of re-taped seams across three rooms ran $540 flat), and popcorn removal finished smooth (230 sq ft ran $575 flat).

New Drywall Installation

For bare studs finished paint-ready (a standard Level 4 finish), plan on $1.60–$3.00 per sq ft of wall and ceiling surface, materials and labor included. A typical 12×12 bedroom with 8-foot ceilings — that's 528 sq ft of surface — runs about $890–$1,660 around Crystal River.

Room Remodel & Replacement

Tearing out old drywall and hauling it off adds $0.60–$1.25 per sq ft on top of new installation — a combined $2.20–$4.25 per sq ft. That same 12×12 bedroom, gutted and re-drywalled, runs about $1,210–$2,310. Opening walls can uncover surprises — water damage, old wiring — and those get priced once they're visible, never guessed at in advance.

Garage Drywall

Garages run $1.55–$3.30 per sq ft depending on finish. Code requires 5/8-inch fire-rated (Type X) board on the wall shared with the house, and on the ceiling when there's living space above it — that's the fire separation, not an upsell. Most two-car garages land between $1,900 and $4,100 finished.

Texture, Skim & Paint

On walls that are already up: skim coating runs $0.95–$1.30 per sq ft, orange-peel or knockdown texture $0.80–$1.85, and primer plus two coats of paint $1.05–$2.85. A typical room's walls — about 415 sq ft of surface — usually land between $750 and $1,980 for texture and paint together.

What Moves the Price

  • Finish level. A full Level 5 skim coat (for gloss paint or bright, raking light) costs more than standard paint-ready Level 4.
  • Ceilings. Overhead work runs roughly 20–25% more than the same area on a wall — lifts, heavier board, two sets of hands.
  • Ceiling height. Taller walls mean longer sheets, scaffolding, and slower work.
  • Texture matching. Blending a patch into existing orange peel or knockdown is hand work, and it's priced like it.
  • Tear-out. Removing old drywall and disposing of it is its own line on the quote.
  • Job size. Small jobs carry a minimum charge; on big jobs the setup spreads over more feet, so the per-foot price drops.

These are planning ranges, not a quote — your final price is confirmed after an in-person look, before any work starts.

A note on materials. These ranges are figured with standard drywall board and the finish level you pick above. Board isn't all the same price, though: moisture- and mold-resistant board — the green or purple board for bathrooms and basements — costs more a sheet than standard board, and on a big job that can push you toward the top of your range, or a little past it. Tell us where the work is and we'll confirm the exact board and the price at the in-person estimate, before any work starts.

Estimate Your Project

1 · Pick your project
Your estimated range

Free — no obligation. Your calculator numbers ride along with the request.

📞 (352) 670-3571